Contractor saws weigh quite a bit more than portable saws, averaging between 150 and 350 pounds, but are still somewhat portable. They have a heavier, cast iron table top, and a motor that is usually more powerful than a jobsite saw. Even so, they’re within prices affordable for more committed hobbyists. Contractor saws can range between $800 and $2,000. They’re good for basic cutting tasks, as well as making home furniture and cabinetry work.
For any kind of professional woodworking and large scale construction work, the cabinet table saw is the one for the job. These types of table saws are often called stationary saws. The motor is protected in a cast iron and steel cabinet that reduces noise and vibration as well. With reduced vibration comes better accuracy which is always the desired effect, especially for professionals. The motor us a powerful 3-5 hp and requires a 220-volt outlet. If you are using it in a home workshop, a special outlet may need to be installed if 220s are not already installed in your garage or shop. Measuring about 28” x 43” and weighing in at over 400 pounds, these table saws were not designed to be portable. The large work surface is ideal for cutting large pieces with ease. Cabinet saws can use a 12” blade with no problem, although a 10” blade is the most commonly used. It is the most expensive of all of the styles of table saws.
Cabinet saws are the prime choice for professional woodworkers. A more powerful induction motor, usually 3 to 5 HP, is enclosed in a cabinet, as part of a super-sturdy overall construction. This type of table saw is ideal for making smooth, straight cuts through hardwoods without worrying about excessive vibration. All that power and stability comes at a price, though. Low-end cabinet saws start around $2,300 and can go past $5,000 for industrial table saws.
Contractor saws weigh quite a bit more than portable saws, averaging between 150 and 350 pounds, but are still somewhat portable. They have a heavier, cast iron table top, and a motor that is usually more powerful than a jobsite saw. Even so, they’re within prices affordable for more committed hobbyists. Contractor saws can range between $800 and $2,000. They’re good for basic cutting tasks, as well as making home furniture and cabinetry work.

best table saw crosscut sled


The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.

After reviewing and thoroughly examining all the options available to us, we’re confident in our recommendation of the Shop Fox W1819 Table Saw as the best overall table saw for any woodshop. If you’re looking for a more portable option that’s a great value for the money, consider the DeWalt DWE7491RS Table Saw. It’s a great combination of power and portability for woodworking hobbyists that’s also suitable for the jobsite.

harbor freight table saw stand


That being said, it is a very basic model. It has great features and is built to the outstanding quality standards of any DeWalt product. Though it doesn’t have all the features that you’ll get on more expensive products from DeWalt or other reputable brands. When I say more expensive, I’m talking about a couple of hundred dollars. So for that reason alone, many of you will take the DeWalt745 over any other.
That being said, it is a very basic model. It has great features and is built to the outstanding quality standards of any DeWalt product. Though it doesn’t have all the features that you’ll get on more expensive products from DeWalt or other reputable brands. When I say more expensive, I’m talking about a couple of hundred dollars. So for that reason alone, many of you will take the DeWalt745 over any other.

best table saw for hobby woodworking


A feather board is simply a piece of wood with slats cut into the end to resemble a feathered edge. A verticle feather board can be clamped at the correct height so that it presses down on the board that you’re cutting as it enters the blade. This is great for preventing kickbacks and for maintaining a constant depth whilst cutting dados and grooves. Remember that a feather board is not going to prevent a kickback due to bad working procedures or neglecting to use the safety equipment properly. It is merely an additional safety mechanism.

The DWE7490X is a great table saw that guarantees convenience and flexibility thanks to its scissor stand. It has been exceptionally designed with a stand that makes the job easier when setting it up. Also, it combines portability and power into one very convenient table saw. Unfortunately, some will find the 87 pounds a bit of a stretch in terms of carrying it around.


Long pieces and whole boards can pose a problem because they will tend to drop off the end of the table. This will cause the feed end to lift. When this happens, you will be applying extra force to keep the wood held down. The way to avoid this from happening is to create a surface on the outfeed side of the saw that is at the same height as the saw’s table. Adjustable trestles are ideal for this purpose. You may have to use pieces of wood as spacers to get the exact height to ensure that the wood feeds through evenly.
There are a lot of obvious reasons why the Skilsaw Portable Worm Drive Table Saw is top quality. Foremost, it is the first worm drive table, therefore, all other similar products are just based on this portable table saw. The Skilsaw is a brass-geared worm drive table saw that provides top power for maximum torque with its 5 HP dual-field motor for improved cutting speed. The selling point is its portability and compact design which makes it transportable anywhere.
While a 50-inch rip capacity might be essential for processing full sheets of wood – common in building tabletops – most projects will do just fine with the 24-28 inches of rip capacity provided by portable and contractor’s table saws. Unless you’re planning on building large furniture or building houses, sticking with any table in the 25- to 35-inch rip capacity range is a safe bet.
Another excellent choice for the hobbyist or at-home handyman, the SKIL 3410-02 10-Inch Table Saw is a great value, giving you a durable build and quality performance at a wallet-friendly price. It doesn’t have the same brand recognition as some of the more expensive options on this list, but reviewers love this machine and say that it’s perfect for woodworking and DIY projects.

best table saw for hobbyist


The latest DeWalt Table Saw is a compact 10-inch job site power saw with a number of great features. First of all, it has a rack and pinion telescoping fence which will let you make fence adjustments easily. This saw has a 24-inch rip capacity so you can use this for a variety of materials. It has an onboard storage system so you can carry tools with ease.
When you buy the DeWalt DW745 a miter gauge, push stick, 24 tooth carbide blade and blade guard come standard with the saw. If you look at all that you’re getting for the price, it is an incredibly attractive offering. You’re backed by the quality standards of a highly respected brand and it comes with the standard 3-year warranty and a 90-day money back guarantee, that you get with all DeWalt products.

best table saw mitre gauge


There are two types of motors used in table saws: universal motors and induction motors. With a universal motor, the power source is linked directly to the blade, providing a whole lot of power. The downside is that these models are generally quite loud. Induction motors, on the other hand, are connected to a belt that then transfers power to the blade. As a result, you get quieter operation and the ability to cut dense materials. The downside is that these models require more preventive maintenance, as you have to adjust the belt’s tension periodically. 

best table saw cabinet


We spent a lot of time setting up and taking down the saws to see how well the stands worked and how easy it was to install and remove the blade guard and anti-kickback pawls. Then we ran a torturous ripping test with 3-in.-thick slabs of oak to find the best table saw. And finally, we used the saws for more conventional tasks like cutting plywood and ripping framing lumber as another test to determine the best table saw.

dewalt 8 1/4 table saw

×