If you want a table saw that helps you deliver products faster, the Bosch 4100-09 could be what you’ve been waiting for. It has a Gravity-Rise stand that is built for efficient and accurate setup and takes down.The portable construction makes it easy to bring to any worksite with minimal trouble. Only weighing 39 pounds, you will have no problem transporting this table saw wherever you need to go. The Bosch 4100-09 is a powerful saw that is made for the kind of high precision cutting that professionals and DIYers are looking for. It has a 15 AMP, 4 HP motor that generates 3,650 RPMs for clean cuts every time.

best table saw deals


There are a lot of great table saws on the market, but we’d have to say the best is the DEWALT DW745 Compact Jobsite Table Saw. This design enables you to be flexible with where you set up shop as well as extremely efficient thanks to the innovative technology that was incorporated into the design. Additionally, it has a 15 amp motor and a 20-inch rip capacity that makes it more than capable of taking on any challenge you throw at it.
If you want a table saw that helps you deliver products faster, the Bosch 4100-09 could be what you’ve been waiting for. It has a Gravity-Rise stand that is built for efficient and accurate setup and takes down.The portable construction makes it easy to bring to any worksite with minimal trouble. Only weighing 39 pounds, you will have no problem transporting this table saw wherever you need to go. The Bosch 4100-09 is a powerful saw that is made for the kind of high precision cutting that professionals and DIYers are looking for. It has a 15 AMP, 4 HP motor that generates 3,650 RPMs for clean cuts every time.

When it comes to this particular style of saw, power is going to be measured either in amperage or in horsepower. The smaller saws, (Bench-top, Jobsite, Contractor, and some Hybrids) will typically have 15-amp motors, which are 1 to 2 HP (Horsepower). They are going to be able to confidently cut through ​wood that is around 2 inches thick with no problems.


A feather board is simply a piece of wood with slats cut into the end to resemble a feathered edge. A verticle feather board can be clamped at the correct height so that it presses down on the board that you’re cutting as it enters the blade. This is great for preventing kickbacks and for maintaining a constant depth whilst cutting dados and grooves. Remember that a feather board is not going to prevent a kickback due to bad working procedures or neglecting to use the safety equipment properly. It is merely an additional safety mechanism.

How and where do you intend to use your table saw? If you plan to take it from one worksite to another then you must use a job site table saw A job site saw is portable, compact and usually has its own stand and may or may not have wheels. Stationary table saws are also called bench top saws because these don’t come with a stand. These rely on a table or a workbench to support the weight of the saw. There are also cabinet table saws which are heavy duty saws that are mounted in a metal or cast-iron cabinet. These saws are very heavy but are usually made with moving wheels and complete cutting features.
A table saw is only as good as its blades. There are a variety of saw blades with varying diameter, arbor size, number of teeth, kerf size, speed, application, and material. Most common table saws use 10 or 12” saw blades with an average number of teeth at24 to 80. And when it comes to the material used, carbide and carbon steel are the most common however you will also find very strong diamond blades.

There is a variety of table saw accessories to keep in mind. Just some of the most common are table extensions, on and off switches, wheels, onboard storage and dust collection features. Additional blades, wrenches, and tables are also a must. Remember that a table saw set is better than a bare tool because you will end up spending more as you buy accessories piece by piece.
If you spend a lot of time working with wood in your garage or workshop, you know the importance of having the best table saw on the market. Many craftsmen find that they feel connected to their work, and because of this they need tools that will work efficiently and reliably. If you’re invested in the art of carpentry, woodcarving, or any other wood related trade, you know that you need a machine that can work efficiently without overwhelming your budget.
In addition, a top-quality fence should move smoothly and have a scale that’s accurate and easy to read. Our favorite is the DeWalt fence. The rack-and-pinion system keeps the fence parallel to the blade, and the micro-adjusting knob allows easy and precise fence positioning. Runners-up in this category for best table saw are the Ridgid and Bosch saws. They both have superb fences, with the added advantage of T-slots for attaching accessories like featherboards.
Kickback is probably more dangerous than cutting yourself with the blade because it can happen so easily and without notice. Kickback happens when the wood becomes jammed and is forced back toward you. This is not a nice experience and often results in pretty serious injuries. Table saws are fitted with a riving knife and often an anti-kickback pawl, make sure these are fitted correctly.
A splitter is a piece of metal that keeps the blade from binding in whatever material you are cutting if the saw kerf starts to close up. The splitter is vertical and sits directly behind the blade. This plays a big part in preventing kickback and should be mounted on the motor assembly so it rises and falls with the saw blades movements. You can also get splitters that can be adjusted to fit the width of the kerf.

10 inch table saw blade


Smaller, portable table saw models have direct-drive motors that can operate on 120 V power to produce 2 HP. This is enough motor power to take on thinner materials. Table saws with more powerful motors are usually stationary saws that produce between 3 to 5 HP. Table saws with stronger motors rely on a belt drive to transfer the power from the motor to the blade and these operate on 240 V.
Blades come in various types and sizes. There are rip blades for cutting along the wood grains, hollow ground blades ideal for various materials, crosscut blades suitable for smooth and precise cuts, and combination blades for that double up as blades for crosscutting and ripping. Depending on what you do the most, it’s necessary to choose the right blade type and size that will get the job done with the most ease.
I appreciate the helpful comparison of the best table saws. I’m fairly new to woodworking, and until recently I was using an old table saw that used to belong to my dad. Long story short, it’s no longer usable, and so I’m looking for a good table saw to buy that’s beginner-friendly. I have my eye on the DEWALT DW745 – evidently it’s really popular and does a great job. I’ve taken a look at some other sites for more ideas. Your guide here is great. What is your opinion on the DW745?
The old designs of table saws did not have the angled capability that newer models have now with their ability to have the blades angled at 45 and 90 degrees. Before these upgraded styles, the table itself had to be tilted which made cutting extremely unsafe. The new styles that accommodate angling the blade for the beveled cuts make things much easier and safer for the user.
One of our favorite features of the device however, would have to be the load speed and maximum cutting depths. The DEWALT DWE7480 Compact Job-Site Table Saw can reach a load speed of 34,800 rpm and can reach a maximum cutting depth of 3 ⅛ inches when working at a 90 degree angle and 2 ¼ inches when working at a 45 degree angle. You’ll love the quick and accurate cuts you’ll be able to make while using this device - it will revolutionize the way you’re able to go about your job.
Measuring approximately 22” x 38”, the contractor table saw is then next size up from the bench style. It typically sits on an open attached stand or base which may or may not be on wheels. It weighs between 200-300 pounds and is still portable but requires more than one person to lift. This style of table saw is good for woodworking shops, hobbyists, small contractors and DIYers. The 1-2 hp motors have enough power and stability to handle more heavy duty job site work and workshop demands. One of the benefits to these saws is that they still run on standard electrical circuits.
Belt drive table saw motors run on a pulley system, most of the time some power is lost through this system, but belt drive blades can cut through thicker timber and hardwoods. They can produce power of around 3 to 5HP and thanks to the motor being mounted further away from the blade with belt drive, the motor will last longer as less dust will get into the motor. One thing to consider though is that belt drive will be in general more expensive and are normally found on heavy cabinet type saws, so this must be considered when working out your budget.
There are two types of motors used in table saws: universal motors and induction motors. With a universal motor, the power source is linked directly to the blade, providing a whole lot of power. The downside is that these models are generally quite loud. Induction motors, on the other hand, are connected to a belt that then transfers power to the blade. As a result, you get quieter operation and the ability to cut dense materials. The downside is that these models require more preventive maintenance, as you have to adjust the belt’s tension periodically. 

chicago electric table saw

×