Obviously, ​this style of saw means that ​you’re dealing with blades sharp and powerful enough to easily cut through wood. You will want to keep your fingers as far away from the blade as possible. Despite your caution, though, you’ll still need to guide the piece being cut in a way that will give you accuracy and precision. This is precisely why the blade guard exists.
If the piece of wood that you’re cutting does not have a straight edge to run along the fence guide, you won’t get an accurate cut. An uneven edge will move back and forth against the fence guide. A good way to create a straight edge to work with is to fasten the piece that you’re cutting to a piece of plywood that has a straight edge. Using screws or nails, you can attach the uneven wood to the straight piece, so that the straight edge runs along the guide rail. Make sure that the straight-edged wood is narrower than the width of your intended cut so that you only cut the piece that is intended to be cut.

It’s not until you get a bunch of saws side by side in the shop that you start to see the difference between a $300 saw and a $500 saw. While the motors are all 15-amp, the more expensive saws have features like soft start to prolong motor and gear life, electronic feedback to maintain blade speed and gearing to maximize torque. If you look under the saws, you’ll see that the more expensive saws also have much beefier motor carriages and better-quality blade-adjusting mechanisms.

circular table saw


A splitter is a piece of metal that keeps the blade from binding in whatever material you are cutting if the saw kerf starts to close up. The splitter is vertical and sits directly behind the blade. This plays a big part in preventing kickback and should be mounted on the motor assembly so it rises and falls with the saw blades movements. You can also get splitters that can be adjusted to fit the width of the kerf. 

10 inch table saw blade


For those looking for something small, these benchtop table saws are just right. Used by contractors who need portable table saws, they’re suitable for quick placement in vehicles and setting up at project sites. Typically, the unit weighs less than 65 pounds and comes equipped with a universal motor. Depending on the model, some come with handy fences. A fence is the part of a saw mounted parallel to the blade, ensuring safe and fast multiple rip cuts.

One thing you must be aware of with a contractor saw is the fact that they can be a lot more difficult to move from job to job, this is something that must be considered before purchasing. For thicker and harder type woods a cabinet table saw maybe the best way to go, especially for the long-term benefits, but for the average mid-sized contractor it’s still a great option. Read More
Contractor saws are a perfect balance between functionality, manoeuvrability and price. These sorts of saws are perfect if you have bigger projects that you’re working on and will stay on site for a few months. This is due to the fact that they are a lot less portable, but that being said they are a great in-between saw as they still have great rip capacity and overall cutting power.
How and where do you intend to use your table saw? If you plan to take it from one worksite to another then you must use a job site table saw A job site saw is portable, compact and usually has its own stand and may or may not have wheels. Stationary table saws are also called bench top saws because these don’t come with a stand. These rely on a table or a workbench to support the weight of the saw. There are also cabinet table saws which are heavy duty saws that are mounted in a metal or cast-iron cabinet. These saws are very heavy but are usually made with moving wheels and complete cutting features.

In layman’s terms, a miter gauge is a device that allows users to set up the angle of the material being cut with a table saw. And while most table saws come with built-in miter gauges, others, well, don’t—which is why the Kreg KMS7102 Table Saw Precision Miter Gauge System is invaluable. Whether you’re replacing an old, worn-out gauge or putting it to use in conjunction with a table saw that didn’t come with its own proprietary gauge, the KMS7102 is specially designed with precision in mind. After all, accuracy is vital to successful woodwork.
Likes: Cuts extremely well and has excellent stability. Its blade guard and riving-knife assembly are locked and unlocked by a lever located conveniently along the table's left edge. A simple, separate shark-fin riving knife can be used when the guard is too big for narrow rip cuts. We appreciate the antiglare surface on the tape ruler that measures the distance from the blade to the fence.
The DeWalt doesn’t go above and beyond here but has some standard safety equipment as part of its Site-Pro Guarding System. The Blade Guard Assembly is a standard clear plastic set of guards that allows the wood to be fed to the blade but shields you from putting hands on the exposed blade in a slip. The guards will lock in a raised position when you need to see the blade—for example, when adjusting the blade height—which lessens the temptation to remove this safety feature when it’s in your way.
The battery operated Milwaukee 2736-21HD Saw relies on a single M18 REDLITHIUM HIGH OUTPUT HD 12.0 battery that generates energy equivalent to a 15 Ah corded saw and produces 6,300 RPM. For the professional carpenter, remodeler, and general contractor, this table saw optimizes for power, productivity, and portability. Included in this machine is the REDLINK Plus intelligence to maximize the performance of your tool and will also protect from overload, overheating, and over discharge. This table saw also features onboard storage for the included accessories, so you don’t have to worry about misplacing them. Keep track of where your saw is on the site with ONE-KEY app and manage the output of how much energy the saw uses from your phone.

best table saw under 1500


The SKILSAW SPT70WT-01 is truly a woodworking marvel, packing a 15-amp Dual Field motor into a surprisingly lightweight yet durable 49-pound frame. Whether you’re an amateur carpenter or a contractor with years of experience under his toolbelt, SKILSAW’s workhorse of a table saw is an invaluable addition to your repertoire thanks to its raw torque and unparalleled 25-inch ripping capacity, meaning tearing through thick sheets of plywood has never been easier.

How many teeth a saw blade has will determine how smooth the cut is. Most blades have from 24-80 teeth. The exceptions to these blades are specialty material specific blades (i.e. for masonry) In general, the more teeth a blade has the smoother the cut will be. The higher tooth count means that the cut speed will be slower as well. You cannot overcome a slower cutting speed by pushing harder on the material. This is a common mistake newbies make. All this will do is cause kickbacks when the saw blade catches and tosses the object back towards to the user at dangerously high speeds.
Is your blade angle taken care of! Good – that means you’re almost done with your safety check process. Now you need to check the material you’re working with. You can’t just pick up any random piece of wood and expect it to fit properly. You’ll have to use wood that is flat and straight. Wood that is curved or that is slightly bowed or cupped will cause issues for you when you try to cut it down – if you need to work with this sort of material you’ll need to find another cutting tool, like the reciprocating saw (click here for full guide).
Our biggest surprise while running the best table saw review tests was in the cutting power and the quality of cut: There wasn’t much difference among them. All these saws ripped through 3-in.-thick oak without hesitating. We tried this test with the stock blades that came on the saws. Then we repeated the test using a top-quality blade in each saw.

best table saw for beginners


You’ll also want to be sure to check that the teeth of the blade are facing towards you since this is the direction that the wood is cut. Once you’ve made sure that the new blade is on properly you can put on the stabilizing parts and nut again. You’ll tighten the nut by putting the spanners on the same way you did before, however, this time you’ll push the spanner in your left hand away from you to tighten the nut instead of towards you.

sawstop table saw


The Porter-Cable looks like a beefed-up version of the Craftsman, with the same blade guard and anti-kickback pawls. This is the only saw in our test with a blade-tilting handwheel, which makes it easier to dial in a precise bevel angle. The motor mount and blade controls on this saw are very sturdy, without much play, which translates to a good-quality cut. Extending the fence for a wide rip requires a bit of effort on this saw, since the rails are stiff. All in all, this is a great saw for the price.

The Bosch 4100-09 10 Inch Table Saw is an expert tool that will be sure to impress its users with the reliable design and easy to use set up system. Our favorite feature was the gravity rise design that allows you to push the device around easily and focus more on getting the job done instead of wasting time trying to set up a complicated device. The tool is also coated in a powder coat that helps to improve the longevity of the device and features a collapsible design that is easy to fold up and down once you get to the job site.

Table saws will use one of two different kinds of drive configurations; Direct-drive motors and Belt-drive motors. In a direct-drive motor, they will link directly to the blade itself and transfer all of the power of the motor to the blade. They tend to last longer than belt drive motors and there is no belt to replace or worry about getting worn out. Belt drive motors transfer power from the motor to the blade through a belt. In this type of configuration, the motor can be offset away from the sawdust which helps the motor last longer. In general, belt drive motors need more preventative maintenance than direct-drive motors do. If you have a belt drive motor, check the tension of your belts as well as checking them for wear periodically to ensure your continued safety.
It’s not until you get a bunch of saws side by side in the shop that you start to see the difference between a $300 saw and a $500 saw. While the motors are all 15-amp, the more expensive saws have features like soft start to prolong motor and gear life, electronic feedback to maintain blade speed and gearing to maximize torque. If you look under the saws, you’ll see that the more expensive saws also have much beefier motor carriages and better-quality blade-adjusting mechanisms.
Along with thinking about how the table saw will be used now, it is important to also consider how you will be using it in the future. Will your usage increase or decrease? Many woodworkers may turn a hobby into a fulltime profession if they are talented at what they do. Why are these considerations important? Because they will give you better insight into the kind of money you should spend on your table. If you are going to go into business for yourself in a year or two, spending the money for a high-quality table now is a good idea. It will save you from having to buy another table in the future to accommodate your new needs as a business rather than just a hobbyist.

metabo table saw

×